Distributed Clock Configuration on SOMANET Circulo-9

AbhilashIngale

Dear MCX Team,

greetings. I am trying to configure distributed clock on a SOMANET Circulo-9. After downloading the .esi file from the slave and uploading it to the ecat.motorcortex.io I performed the following steps -

Added the Assign Activate value from the .esi file.
Added the value 1000000 (ns) in the field CycleTimeSync0 and and 0(ns) in the field CycleTimeShift0.

Checked the parameters in Process Data SyncManager (screenshot). These parameter values in the .esi file are:

<Sm DefaultSize="1024" StartAddress="#x1000" ControlByte="#x26" Enable="1">MBoxOut</Sm>
				<Sm DefaultSize="1024" StartAddress="#x1400" ControlByte="#x22" Enable="1">MBoxIn</Sm>
				<Sm MinSize="1" MaxSize="300" DefaultSize="35" StartAddress="#x1800" ControlByte="#x64" Enable="1">Outputs</Sm>
				<Sm MinSize="1" MaxSize="300" DefaultSize="47" StartAddress="#x1C00" ControlByte="#x20" Enable="1">Inputs</Sm>

However, I still get the 0x001B: "Sync manager watchdog" message in the dmesg log. I also see Failed to receive AL state datagram: Datagram initialized.

Could you share any suggestions on what might be going wrong here on my setup?

AbhilashIngale

Here's the 'complete' dmesg log

[ 1385.502380] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1386.502384] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1387.026591] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Down
[ 1387.026791] EtherCAT 0: Link state of ecm0 changed to DOWN.
[ 1387.502380] EtherCAT WARNING 0: 175 datagrams TIMED OUT!
[ 1420.554194] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 1420.661790] EtherCAT 0: Link state of ecm0 changed to UP.
[ 1421.502385] EtherCAT WARNING 0: 280 datagrams TIMED OUT!
[ 1422.502385] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1423.502385] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1424.502385] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1425.502386] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1426.502387] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1427.502386] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1428.502386] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1429.502385] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1430.502384] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1431.502383] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1432.502384] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1433.502384] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1434.502383] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1435.502386] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1436.502380] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1437.502386] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1438.502386] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1439.502387] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1440.502386] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1441.502386] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1442.502386] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1443.502386] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1444.502387] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1445.502387] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1446.502387] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1447.502386] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1448.502386] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1449.502387] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1450.502387] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1451.502385] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1452.502382] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1453.502387] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1454.502386] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1455.502387] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1456.502388] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1457.502387] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1458.502387] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1459.502387] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1460.502387] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1461.502384] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1462.502387] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1463.502388] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1464.502388] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1465.502387] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1466.502388] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1467.502387] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1468.502382] EtherCAT WARNING 0: 334 datagrams TIMED OUT!
[ 1469.502388] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1470.502387] EtherCAT WARNING 0: 333 datagrams TIMED OUT!
[ 1470.756628] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Down
[ 1470.756795] EtherCAT 0: Link state of ecm0 changed to DOWN.
[ 1471.502387] EtherCAT WARNING 0: 85 datagrams TIMED OUT!
[ 1637.896562] fbcon: inteldrmfb (fb0) is primary device
[ 1637.911393] usb 1-4: new high-speed USB device number 3 using xhci_hcd
[ 1637.941425] Console: switching to colour frame buffer device 240x67
[ 1637.958262] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 1638.042534] hub 1-4:1.0: USB hub found
[ 1638.043052] hub 1-4:1.0: 4 ports detected
[ 1653.238387] usb 1-4.4: new full-speed USB device number 4 using xhci_hcd
[ 1653.352902] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:15.0/usb1/1-4/1-4.4/1-4.4:1.0/0003:046D:C52B.0001/input/input2
[ 1653.405884] hid-generic 0003:046D:C52B.0001: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:15.0-4.4/input0
[ 1653.409594] input: Logitech USB Receiver Mouse as /devices/pci0000:00/0000:00:15.0/usb1/1-4/1-4.4/1-4.4:1.1/0003:046D:C52B.0002/input/input3
[ 1653.409783] input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:15.0/usb1/1-4/1-4.4/1-4.4:1.1/0003:046D:C52B.0002/input/input4
[ 1653.462562] input: Logitech USB Receiver System Control as /devices/pci0000:00/0000:00:15.0/usb1/1-4/1-4.4/1-4.4:1.1/0003:046D:C52B.0002/input/input5
[ 1653.462717] hid-generic 0003:046D:C52B.0002: input,hiddev96: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:15.0-4.4/input1
[ 1653.465985] hid-generic 0003:046D:C52B.0003: hiddev97: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:15.0-4.4/input2
[ 1669.697151] usb 1-4: USB disconnect, device number 3
[ 1669.697156] usb 1-4.4: USB disconnect, device number 4
[ 1681.296389] usb 1-4: new high-speed USB device number 5 using xhci_hcd
[ 1681.426556] hub 1-4:1.0: USB hub found
[ 1681.426825] hub 1-4:1.0: 4 ports detected
[ 1681.726393] usb 1-4.4: new full-speed USB device number 6 using xhci_hcd
[ 1681.841300] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:15.0/usb1/1-4/1-4.4/1-4.4:1.0/0003:046D:C52B.0004/input/input7
[ 1681.893887] hid-generic 0003:046D:C52B.0004: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:15.0-4.4/input0
[ 1681.898438] input: Logitech USB Receiver Mouse as /devices/pci0000:00/0000:00:15.0/usb1/1-4/1-4.4/1-4.4:1.1/0003:046D:C52B.0005/input/input8
[ 1681.898627] input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:15.0/usb1/1-4/1-4.4/1-4.4:1.1/0003:046D:C52B.0005/input/input9
[ 1681.950568] input: Logitech USB Receiver System Control as /devices/pci0000:00/0000:00:15.0/usb1/1-4/1-4.4/1-4.4:1.1/0003:046D:C52B.0005/input/input10
[ 1681.950713] hid-generic 0003:046D:C52B.0005: input,hiddev96: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:15.0-4.4/input1
[ 1681.953902] hid-generic 0003:046D:C52B.0006: hiddev97: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:15.0-4.4/input2
[ 1723.722274] usb 1-4: USB disconnect, device number 5
[ 1723.722280] usb 1-4.4: USB disconnect, device number 6
[ 1749.172391] usb 1-4: new high-speed USB device number 7 using xhci_hcd
[ 1749.302762] hub 1-4:1.0: USB hub found
[ 1749.303010] hub 1-4:1.0: 4 ports detected
[ 1749.605392] usb 1-4.4: new full-speed USB device number 8 using xhci_hcd
[ 1749.720439] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:15.0/usb1/1-4/1-4.4/1-4.4:1.0/0003:046D:C52B.0007/input/input12
[ 1749.773862] hid-generic 0003:046D:C52B.0007: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:15.0-4.4/input0
[ 1749.777700] input: Logitech USB Receiver Mouse as /devices/pci0000:00/0000:00:15.0/usb1/1-4/1-4.4/1-4.4:1.1/0003:046D:C52B.0008/input/input13
[ 1749.778132] input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:15.0/usb1/1-4/1-4.4/1-4.4:1.1/0003:046D:C52B.0008/input/input14
[ 1749.829566] input: Logitech USB Receiver System Control as /devices/pci0000:00/0000:00:15.0/usb1/1-4/1-4.4/1-4.4:1.1/0003:046D:C52B.0008/input/input15
[ 1749.829718] hid-generic 0003:046D:C52B.0008: input,hiddev96: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:15.0-4.4/input1
[ 1749.832890] hid-generic 0003:046D:C52B.0009: hiddev97: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:15.0-4.4/input2
[ 1799.107225] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 1829.282031] usb 1-4: USB disconnect, device number 7
[ 1829.282036] usb 1-4.4: USB disconnect, device number 8
[ 1865.585215] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 1865.798676] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1865.798771] br0: port 1(eth0) entered blocking state
[ 1865.798774] br0: port 1(eth0) entered forwarding state
[ 1865.799063] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[ 1947.175265] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 1947.175569] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 1947.175817] EtherCAT 0: Link state of ecm0 changed to UP.
[ 1947.183415] EtherCAT 0: 1 slave(s) responding on main device.
[ 1947.183420] EtherCAT 0: Slave states on main device: INIT.
[ 1947.189414] EtherCAT 0: Scanning bus.
[ 1952.514414] EtherCAT ERROR 0-main-0: Timeout while setting state PREOP.
[ 1952.515420] EtherCAT 0: Bus scanning completed in 5332 ms.
[ 1952.515426] EtherCAT 0: Using slave main-0 as DC reference clock.
[ 1952.516421] EtherCAT WARNING 0: 2 datagrams TIMED OUT!
[ 2076.468440] EtherCAT 0: Master thread exited.
[ 2076.468456] EtherCAT 0: Starting EtherCAT-IDLE thread.
[ 2076.549055] EtherCAT 0: Releasing master...
[ 2076.549062] EtherCAT 0: Released.
[ 2079.477624] EtherCAT ERROR 0-main-0: Failed to set state PREOP: No response.
[ 2107.566496] EtherCAT 0: Master thread exited.
[ 2107.566609] EtherCAT 0: Releasing main device 00:01:C0:2F:E0:C6.
[ 2107.573659] ec_generic: Unloading.
[ 2107.583609] EtherCAT: Master module cleaned up.
[ 2134.796247] br0: port 2(eth1) entered blocking state
[ 2134.796322] br0: port 2(eth1) entered disabled state
[ 2134.799318] device eth1 entered promiscuous mode
[ 2141.149277] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 2142.828238] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 2142.830924] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 2142.833454] br0: port 2(eth1) entered blocking state
[ 2142.835828] br0: port 2(eth1) entered forwarding state
[ 2182.492553] br0: port 2(eth1) entered disabled state
[ 2194.044275] device eth1 left promiscuous mode
[ 2194.046839] br0: port 2(eth1) entered disabled state
[ 2194.090073] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 2195.750233] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 2195.753004] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 2213.839523] EtherCAT: Master driver 1.5.2-vecsyn-5 gf0c7a0cb
[ 2213.842186] EtherCAT: 1 master waiting for devices.
[ 2213.851086] ec_generic: EtherCAT master generic Ethernet device module 1.5.2-vecsyn-5 gf0c7a0cb
[ 2213.853697] EtherCAT: Accepting 00:01:C0:2F:E0:C6 as main device for master 0.
[ 2213.856284] ec_generic: Binding socket to interface 5 (eth1).
[ 2213.864574] EtherCAT 0: Starting EtherCAT-IDLE thread.
[ 2213.867554] EtherCAT 0: Link state of ecm0 changed to UP.
[ 2213.868795] EtherCAT 0: 1 slave(s) responding on main device.
[ 2213.868799] EtherCAT 0: Slave states on main device: INIT.
[ 2213.869452] EtherCAT 0: Scanning bus.
[ 2216.939649] EtherCAT ERROR 0-main-0: Failed to set state INIT: No response.
[ 2216.942256] EtherCAT 0: Bus scanning completed in 3073 ms.
[ 2216.944821] EtherCAT 0: Using slave main-0 as DC reference clock.
[ 2224.184710] EtherCAT: Requesting master 0...
[ 2224.184716] EtherCAT: Successfully requested master 0.
[ 2227.184962] EtherCAT ERROR 0-main-0: Failed to set state INIT: No response.
[ 2227.250855] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[ 2227.250862] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 0000000056536293.
[ 2227.251205] EtherCAT 0: Master thread exited.
[ 2227.251211] EtherCAT 0: Starting EtherCAT-OP thread.
[ 2227.251302] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[ 2495.105323] EtherCAT 0: Master thread exited.
[ 2495.105343] EtherCAT 0: Starting EtherCAT-IDLE thread.
[ 2495.177651] EtherCAT 0: Releasing master...
[ 2495.177657] EtherCAT 0: Released.
[ 2498.106373] EtherCAT ERROR 0-main-0: Failed to set state INIT: No response.
[ 2504.675493] EtherCAT 0: Master thread exited.
[ 2504.678062] EtherCAT 0: Releasing main device 00:01:C0:2F:E0:C6.
[ 2504.688648] ec_generic: Unloading.
[ 2504.700363] EtherCAT: Master module cleaned up.
[ 2532.073494] br0: port 2(eth1) entered blocking state
[ 2532.076025] br0: port 2(eth1) entered disabled state
[ 2532.079081] device eth1 entered promiscuous mode
[ 2542.863302] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 2544.524256] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 2544.526991] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 2544.529570] br0: port 2(eth1) entered blocking state
[ 2544.531974] br0: port 2(eth1) entered forwarding state
[ 2583.588075] br0: port 2(eth1) entered disabled state
[ 2590.590360] device eth1 left promiscuous mode
[ 2590.593048] br0: port 2(eth1) entered disabled state
[ 2590.642136] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 2592.357259] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 2592.359967] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 2602.300265] EtherCAT: Master driver 1.5.2-vecsyn-5 gf0c7a0cb
[ 2602.302974] EtherCAT: 1 master waiting for devices.
[ 2602.311331] ec_generic: EtherCAT master generic Ethernet device module 1.5.2-vecsyn-5 gf0c7a0cb
[ 2602.313827] EtherCAT: Accepting 00:01:C0:2F:E0:C6 as main device for master 0.
[ 2602.316252] ec_generic: Binding socket to interface 5 (eth1).
[ 2602.324604] EtherCAT 0: Starting EtherCAT-IDLE thread.
[ 2602.327386] EtherCAT 0: Link state of ecm0 changed to UP.
[ 2602.328567] EtherCAT 0: 1 slave(s) responding on main device.
[ 2602.328570] EtherCAT 0: Slave states on main device: INIT.
[ 2602.329233] EtherCAT 0: Scanning bus.
[ 2605.400655] EtherCAT ERROR 0-main-0: Failed to set state INIT: No response.
[ 2605.403057] EtherCAT 0: Bus scanning completed in 3074 ms.
[ 2605.405364] EtherCAT 0: Using slave main-0 as DC reference clock.
[ 2609.359673] EtherCAT: Requesting master 0...
[ 2609.359677] EtherCAT: Successfully requested master 0.
[ 2612.361255] EtherCAT ERROR 0-main-0: Failed to set state INIT: No response.
[ 2612.517864] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[ 2612.517871] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 000000006563d14a.
[ 2612.518983] EtherCAT 0: Master thread exited.
[ 2612.518990] EtherCAT 0: Starting EtherCAT-OP thread.
[ 3007.149666] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[ 3007.154538] br0: port 1(eth0) entered disabled state
[ 3027.541197] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
[ 3027.749798] br0: port 1(eth0) entered blocking state
[ 3027.749802] br0: port 1(eth0) entered forwarding state
[ 3038.874665] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[ 3038.878532] br0: port 1(eth0) entered disabled state
[ 3042.344284] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 3042.558781] br0: port 1(eth0) entered blocking state
[ 3042.558785] br0: port 1(eth0) entered forwarding state
[ 3379.664259] EtherCAT 0: Master thread exited.
[ 3379.664278] EtherCAT 0: Starting EtherCAT-IDLE thread.
[ 3379.665748] EtherCAT ERROR 0-main-0: Failed to receive AL state datagram: Datagram initialized.
[ 3379.737683] EtherCAT 0: Releasing master...
[ 3379.737689] EtherCAT 0: Released.
[ 3380.106631] EtherCAT WARNING: Datagram 00000000beab9360 (master-fsm) was SKIPPED 1 time.
[ 3382.665645] EtherCAT ERROR 0-main-0: Failed to set state INIT: No response.
[ 3390.965014] EtherCAT 0: Master thread exited.
[ 3390.967399] EtherCAT 0: Releasing main device 00:01:C0:2F:E0:C6.
[ 3390.977711] ec_generic: Unloading.
[ 3390.990437] EtherCAT: Master module cleaned up.
[ 3419.061533] br0: port 2(eth1) entered blocking state
[ 3419.063864] br0: port 2(eth1) entered disabled state
[ 3419.066557] device eth1 entered promiscuous mode
[ 3436.603229] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 3438.282298] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 3438.284944] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 3438.287399] br0: port 2(eth1) entered blocking state
[ 3438.289712] br0: port 2(eth1) entered forwarding state
[ 3481.955537] br0: port 2(eth1) entered disabled state
[ 3487.206700] device eth1 left promiscuous mode
[ 3487.209314] br0: port 2(eth1) entered disabled state
[ 3487.255736] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 3488.917300] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 3488.919928] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 3500.386131] EtherCAT: Master driver 1.5.2-vecsyn-5 gf0c7a0cb
[ 3500.388757] EtherCAT: 1 master waiting for devices.
[ 3500.396695] ec_generic: EtherCAT master generic Ethernet device module 1.5.2-vecsyn-5 gf0c7a0cb
[ 3500.399086] EtherCAT: Accepting 00:01:C0:2F:E0:C6 as main device for master 0.
[ 3500.401451] ec_generic: Binding socket to interface 5 (eth1).
[ 3500.409635] EtherCAT 0: Starting EtherCAT-IDLE thread.
[ 3500.412247] EtherCAT 0: Link state of ecm0 changed to UP.
[ 3500.413537] EtherCAT 0: 1 slave(s) responding on main device.
[ 3500.413540] EtherCAT 0: Slave states on main device: INIT.
[ 3500.414171] EtherCAT 0: Scanning bus.
[ 3503.486572] EtherCAT ERROR 0-main-0: Failed to set state INIT: No response.
[ 3503.488952] EtherCAT 0: Bus scanning completed in 3075 ms.
[ 3503.491269] EtherCAT 0: Using slave main-0 as DC reference clock.
[ 3506.297664] EtherCAT: Requesting master 0...
[ 3506.297669] EtherCAT: Successfully requested master 0.
[ 3509.299408] EtherCAT ERROR 0-main-0: Failed to set state INIT: No response.
[ 3509.412914] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[ 3509.412921] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 000000006563d14a.
[ 3509.413399] EtherCAT 0: Master thread exited.
[ 3509.413405] EtherCAT 0: Starting EtherCAT-OP thread.
[ 6469.268827] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Down
[ 6469.269026] EtherCAT 0: Link state of ecm0 changed to DOWN.
[ 6469.269360] EtherCAT ERROR 0-main-0: Failed to receive AL state datagram: Datagram error.
[ 6469.270360] EtherCAT 0: 0 slave(s) responding on main device.
[ 6523.951823] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[ 6523.955703] br0: port 1(eth0) entered disabled state
[ 6527.534341] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 6527.742945] br0: port 1(eth0) entered blocking state
[ 6527.742949] br0: port 1(eth0) entered forwarding state
[ 6536.471822] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[ 6536.476696] br0: port 1(eth0) entered disabled state
[ 6543.753330] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 6543.965929] br0: port 1(eth0) entered blocking state
[ 6543.965934] br0: port 1(eth0) entered forwarding state
[ 6659.445830] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[ 6659.449705] br0: port 1(eth0) entered disabled state
[ 6670.546439] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 6670.546851] br0: port 1(eth0) entered blocking state
[ 6670.546854] br0: port 1(eth0) entered forwarding state
[ 6678.571828] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[ 6678.575711] br0: port 1(eth0) entered disabled state
[ 6684.563349] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 6684.563788] br0: port 1(eth0) entered blocking state
[ 6684.563791] br0: port 1(eth0) entered forwarding state
[ 6698.567829] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[ 6698.572700] br0: port 1(eth0) entered disabled state
[ 6709.143384] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 6709.349936] br0: port 1(eth0) entered blocking state
[ 6709.349940] br0: port 1(eth0) entered forwarding state
[ 6722.355832] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[ 6722.361705] br0: port 1(eth0) entered disabled state
[ 6725.791313] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 6725.997937] br0: port 1(eth0) entered blocking state
[ 6725.997941] br0: port 1(eth0) entered forwarding state
[ 6816.057834] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[ 6816.062708] br0: port 1(eth0) entered disabled state
[ 6819.495533] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 6819.701957] br0: port 1(eth0) entered blocking state
[ 6819.701961] br0: port 1(eth0) entered forwarding state
[ 6828.901833] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[ 6828.906725] br0: port 1(eth0) entered disabled state
[ 6834.876449] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 6834.876855] br0: port 1(eth0) entered blocking state
[ 6834.876858] br0: port 1(eth0) entered forwarding state
[56307.194111] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[56307.198989] br0: port 1(eth0) entered disabled state
[87476.243050] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[87476.449660] br0: port 1(eth0) entered blocking state
[87476.449664] br0: port 1(eth0) entered forwarding state
[87747.507592] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[87747.511469] br0: port 1(eth0) entered disabled state
[87750.957062] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[87751.066700] br0: port 1(eth0) entered blocking state
[87751.066705] br0: port 1(eth0) entered forwarding state
[87763.178559] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Down
[87763.182446] br0: port 1(eth0) entered disabled state
[87771.018168] igb 0000:02:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[87771.122659] br0: port 1(eth0) entered blocking state
[87771.122663] br0: port 1(eth0) entered forwarding state
[87886.783167] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[87886.783771] EtherCAT 0: Link state of ecm0 changed to UP.
[87886.794109] EtherCAT 0: 1 slave(s) responding on main device.
[87886.794113] EtherCAT 0: Slave states on main device: INIT.
[87886.800107] EtherCAT 0: Scanning bus.
[87892.125111] EtherCAT ERROR 0-main-0: Timeout while setting state PREOP.
[87892.126112] EtherCAT 0: Bus scanning completed in 5332 ms.
[87892.126119] EtherCAT 0: Using slave main-0 as DC reference clock.
[87892.127106] EtherCAT WARNING 0: 3 datagrams TIMED OUT!
[87949.959570] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Down
[87949.959775] EtherCAT 0: Link state of ecm0 changed to DOWN.
[87949.960111] EtherCAT ERROR 0-main-0: Failed to receive AL state datagram: Datagram error.
[87949.961110] EtherCAT 0: 0 slave(s) responding on main device.
[88021.022178] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[88021.022777] EtherCAT 0: Link state of ecm0 changed to UP.
[88021.033114] EtherCAT 0: 1 slave(s) responding on main device.
[88021.033119] EtherCAT 0: Slave states on main device: INIT.
[88021.039132] EtherCAT 0: Scanning bus.
[88023.239115] EtherCAT 0: Bus scanning completed in 2206 ms.
[88023.239122] EtherCAT 0: Using slave main-0 as DC reference clock.
[88023.240121] EtherCAT WARNING 0: 3 datagrams TIMED OUT!
[88023.247114] EtherCAT 0: Slave states on main device: PREOP.
[88476.747402] EtherCAT 0: Master thread exited.
[88476.747420] EtherCAT 0: Starting EtherCAT-IDLE thread.
[88476.751609] EtherCAT 0: Slave states on main device: INIT.
[88476.760575] EtherCAT 0: Slave states on main device: PREOP.
[88476.821745] EtherCAT 0: Releasing master...
[88476.821780] EtherCAT 0: Released.
[88478.005759] EtherCAT 0: Master thread exited.
[88478.008129] EtherCAT 0: Releasing main device 00:01:C0:2F:E0:C6.
[88478.014620] ec_generic: Unloading.
[88478.026608] EtherCAT: Master module cleaned up.
[88480.103055] br0: port 2(eth1) entered blocking state
[88480.105392] br0: port 2(eth1) entered disabled state
[88480.107897] device eth1 entered promiscuous mode
[88480.653097] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[88482.332212] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[88482.334809] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[88482.337265] br0: port 2(eth1) entered blocking state
[88482.339625] br0: port 2(eth1) entered forwarding state
[88536.978623] br0: port 2(eth1) entered disabled state
[88545.042093] device eth1 left promiscuous mode
[88545.044469] br0: port 2(eth1) entered disabled state
[88545.088915] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[88546.771213] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[88546.773856] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[88556.300152] EtherCAT: Master driver 1.5.2-vecsyn-5 gf0c7a0cb
[88556.302826] EtherCAT: 1 master waiting for devices.
[88556.311571] ec_generic: EtherCAT master generic Ethernet device module 1.5.2-vecsyn-5 gf0c7a0cb
[88556.313965] EtherCAT: Accepting 00:01:C0:2F:E0:C6 as main device for master 0.
[88556.316787] ec_generic: Binding socket to interface 5 (eth1).
[88556.325546] EtherCAT 0: Starting EtherCAT-IDLE thread.
[88556.328219] EtherCAT 0: Link state of ecm0 changed to UP.
[88556.329355] EtherCAT 0: 1 slave(s) responding on main device.
[88556.329358] EtherCAT 0: Slave states on main device: PREOP.
[88556.329952] EtherCAT 0: Scanning bus.
[88556.616823] EtherCAT 0: Bus scanning completed in 288 ms.
[88556.619096] EtherCAT 0: Using slave main-0 as DC reference clock.
[88556.627491] EtherCAT 0: Slave states on main device: INIT.
[88556.637019] EtherCAT 0: Slave states on main device: PREOP.
[88562.644937] EtherCAT: Requesting master 0...
[88562.644942] EtherCAT: Successfully requested master 0.
[88565.845828] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[88565.845835] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 0000000056536293.
[88565.845915] EtherCAT 0: Master thread exited.
[88565.845921] EtherCAT 0: Starting EtherCAT-OP thread.
[88692.389811] EtherCAT 0: Link state of ecm0 changed to DOWN.
[88692.391117] EtherCAT ERROR 0-main-0: Failed to receive AL state datagram: Datagram error.
[88692.392117] EtherCAT 0: 0 slave(s) responding on main device.
[88692.846094] EtherCAT WARNING 0: 2 datagrams TIMED OUT!
[88693.477534] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[88695.148112] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[88695.148478] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[88695.148812] EtherCAT 0: Link state of ecm0 changed to UP.
[88695.159164] EtherCAT 0: 1 slave(s) responding on main device.
[88695.159168] EtherCAT 0: Slave states on main device: PREOP.
[88695.165131] EtherCAT 0: Scanning bus.
[88696.499155] EtherCAT 0: Bus scanning completed in 1340 ms.
[88696.499163] EtherCAT 0: Using slave main-0 as DC reference clock.
[88696.500152] EtherCAT WARNING 0: 3 datagrams TIMED OUT!
[88699.721031] EtherCAT 0: Master thread exited.
[88699.721050] EtherCAT 0: Starting EtherCAT-IDLE thread.
[88699.724517] EtherCAT 0: Slave states on main device: INIT.
[88699.730902] EtherCAT 0: Slave states on main device: PREOP.
[88699.803756] EtherCAT 0: Releasing master...
[88699.803763] EtherCAT 0: Released.
[88700.996179] EtherCAT 0: Master thread exited.
[88700.998537] EtherCAT 0: Releasing main device 00:01:C0:2F:E0:C6.
[88701.006624] ec_generic: Unloading.
[88701.019212] EtherCAT: Master module cleaned up.
[88703.093575] br0: port 2(eth1) entered blocking state
[88703.095819] br0: port 2(eth1) entered disabled state
[88703.098144] device eth1 entered promiscuous mode
[88703.642484] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[88705.286223] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[88705.288753] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[88705.292120] br0: port 2(eth1) entered blocking state
[88705.294452] br0: port 2(eth1) entered forwarding state
[89001.471724] br0: port 2(eth1) entered disabled state
[89001.988933] device eth1 left promiscuous mode
[89001.991178] br0: port 2(eth1) entered disabled state
[89002.040153] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[89003.072626] EtherCAT: Master driver 1.5.2-vecsyn-5 gf0c7a0cb
[89003.075114] EtherCAT: 1 master waiting for devices.
[89003.084001] ec_generic: EtherCAT master generic Ethernet device module 1.5.2-vecsyn-5 gf0c7a0cb
[89003.086307] EtherCAT: Accepting 00:01:C0:2F:E0:C6 as main device for master 0.
[89003.088602] ec_generic: Binding socket to interface 5 (eth1).
[89003.096576] EtherCAT 0: Starting EtherCAT-IDLE thread.
[89003.718163] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[89003.720805] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[89003.720814] EtherCAT 0: Link state of ecm0 changed to UP.
[89003.728835] EtherCAT 0: 1 slave(s) responding on main device.
[89003.731290] EtherCAT 0: Slave states on main device: SAFEOP + ERROR.
[89003.734173] EtherCAT 0: Scanning bus.
[89003.737223] EtherCAT WARNING 0-main-0: Slave has state error bit set (SAFEOP + ERROR)!
[89003.852355] EtherCAT 0: Bus scanning completed in 118 ms.
[89003.852362] EtherCAT 0: Using slave main-0 as DC reference clock.
[89003.855540] EtherCAT ERROR 0-main-0: AL status message 0x001B: "Sync manager watchdog".
[89003.857644] EtherCAT 0: Slave states on main device: SAFEOP.
[89003.857651] EtherCAT 0-main-0: Acknowledged state SAFEOP.
[89003.859762] EtherCAT 0: Slave states on main device: INIT.
[89003.868205] EtherCAT 0: Slave states on main device: PREOP.
[89003.974739] EtherCAT: Requesting master 0...
[89003.974744] EtherCAT: Successfully requested master 0.
[89007.164852] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[89007.164859] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 00000000c56c566b.
[89007.165462] EtherCAT 0: Master thread exited.
[89007.165470] EtherCAT 0: Starting EtherCAT-OP thread.
[89007.165949] EtherCAT WARNING 0: 6 datagrams TIMED OUT!
[89019.597967] EtherCAT 0: Master thread exited.
[89019.597984] EtherCAT 0: Starting EtherCAT-IDLE thread.
[89019.600629] EtherCAT ERROR 0-main-0: Failed to receive AL state datagram: Datagram initialized.
[89019.603732] EtherCAT 0: Slave states on main device: INIT.
[89019.610267] EtherCAT 0: Slave states on main device: PREOP.
[89019.673120] EtherCAT 0: Releasing master...
[89019.673127] EtherCAT 0: Released.
[89020.115674] EtherCAT WARNING: Datagram 000000003dabcaec (master-fsm) was SKIPPED 1 time.
[89020.856487] EtherCAT 0: Master thread exited.
[89020.858843] EtherCAT 0: Releasing main device 00:01:C0:2F:E0:C6.
[89020.867622] ec_generic: Unloading.
[89020.879754] EtherCAT: Master module cleaned up.
[89022.953924] br0: port 2(eth1) entered blocking state
[89022.956207] br0: port 2(eth1) entered disabled state
[89022.958663] device eth1 entered promiscuous mode
[89023.504205] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[89025.164236] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[89025.166812] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[89025.169226] br0: port 2(eth1) entered blocking state
[89025.171532] br0: port 2(eth1) entered forwarding state
[89076.635317] br0: port 2(eth1) entered disabled state
[89077.152892] device eth1 left promiscuous mode
[89077.155743] br0: port 2(eth1) entered disabled state
[89077.202559] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[89078.234492] EtherCAT: Master driver 1.5.2-vecsyn-5 gf0c7a0cb
[89078.237009] EtherCAT: 1 master waiting for devices.
[89078.245231] ec_generic: EtherCAT master generic Ethernet device module 1.5.2-vecsyn-5 gf0c7a0cb
[89078.247608] EtherCAT: Accepting 00:01:C0:2F:E0:C6 as main device for master 0.
[89078.249949] ec_generic: Binding socket to interface 5 (eth1).
[89078.257573] EtherCAT 0: Starting EtherCAT-IDLE thread.
[89078.881174] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[89078.883845] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[89078.884595] EtherCAT 0: Link state of ecm0 changed to UP.
[89078.891630] EtherCAT 0: 1 slave(s) responding on main device.
[89078.894143] EtherCAT 0: Slave states on main device: SAFEOP + ERROR.
[89078.897040] EtherCAT 0: Scanning bus.
[89078.900039] EtherCAT WARNING 0-main-0: Slave has state error bit set (SAFEOP + ERROR)!
[89079.014696] EtherCAT 0: Bus scanning completed in 118 ms.
[89079.014703] EtherCAT 0: Using slave main-0 as DC reference clock.
[89079.017950] EtherCAT ERROR 0-main-0: AL status message 0x001B: "Sync manager watchdog".
[89079.020059] EtherCAT 0: Slave states on main device: SAFEOP.
[89079.020065] EtherCAT 0-main-0: Acknowledged state SAFEOP.
[89079.022190] EtherCAT 0: Slave states on main device: INIT.
[89079.030692] EtherCAT 0: Slave states on main device: PREOP.
[89079.131534] EtherCAT: Requesting master 0...
[89079.131540] EtherCAT: Successfully requested master 0.
[89082.242846] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[89082.242853] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 00000000b4ecb564.
[89082.243472] EtherCAT 0: Master thread exited.
[89082.243479] EtherCAT 0: Starting EtherCAT-OP thread.
[89082.248644] EtherCAT WARNING 0: 5 datagrams TIMED OUT!
[89652.225679] EtherCAT 0: Master thread exited.
[89652.225699] EtherCAT 0: Starting EtherCAT-IDLE thread.
[89652.229634] EtherCAT 0: Slave states on main device: INIT.
[89652.235828] EtherCAT 0: Slave states on main device: PREOP.
[89652.302847] EtherCAT 0: Releasing master...
[89652.302853] EtherCAT 0: Released.
[89654.302313] EtherCAT: Requesting master 0...
[89654.302319] EtherCAT: Successfully requested master 0.
[89657.382880] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[89657.382886] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 0000000006a5d054.
[89657.383414] EtherCAT 0: Master thread exited.
[89657.383434] EtherCAT 0: Starting EtherCAT-OP thread.
[89657.384491] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[89657.409495] EtherCAT 0: Slave states on main device: INIT.
[89657.421494] EtherCAT 0: Slave states on main device: PREOP.
[89657.753494] EtherCAT 0: Slave states on main device: SAFEOP.
[89657.757492] EtherCAT 0: Slave states on main device: OP.
[90040.119892] EtherCAT 0: Master thread exited.
[90040.120018] EtherCAT 0: Starting EtherCAT-IDLE thread.
[90040.125857] EtherCAT 0: Slave states on main device: INIT.
[90040.132107] EtherCAT 0: Slave states on main device: PREOP.
[90040.201728] EtherCAT 0: Releasing master...
[90040.201735] EtherCAT 0: Released.
[90042.194608] EtherCAT: Requesting master 0...
[90042.194614] EtherCAT: Successfully requested master 0.
[90045.326918] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[90045.326925] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 0000000020105f58.
[90045.327246] EtherCAT 0: Master thread exited.
[90045.327252] EtherCAT 0: Starting EtherCAT-OP thread.
[90045.327343] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[90045.348360] EtherCAT 0: Slave states on main device: INIT.
[90045.360357] EtherCAT 0: Slave states on main device: PREOP.
[90045.692357] EtherCAT 0: Slave states on main device: SAFEOP.
[90045.696357] EtherCAT 0: Slave states on main device: OP.
[90192.084483] EtherCAT 0: Master thread exited.
[90192.084501] EtherCAT 0: Starting EtherCAT-IDLE thread.
[90192.089774] EtherCAT 0: Slave states on main device: INIT.
[90192.095979] EtherCAT 0: Slave states on main device: PREOP.
[90192.162720] EtherCAT 0: Releasing master...
[90192.162726] EtherCAT 0: Released.
[90194.155305] EtherCAT: Requesting master 0...
[90194.155311] EtherCAT: Successfully requested master 0.
[90197.246935] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[90197.246942] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 0000000054c7af0c.
[90197.248014] EtherCAT 0: Master thread exited.
[90197.248021] EtherCAT 0: Starting EtherCAT-OP thread.
[90197.249230] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[90197.276245] EtherCAT 0: Slave states on main device: INIT.
[90197.288244] EtherCAT 0: Slave states on main device: PREOP.
[90197.620241] EtherCAT 0: Slave states on main device: SAFEOP.
[90197.624243] EtherCAT 0: Slave states on main device: OP.
[90214.645483] EtherCAT 0: Master thread exited.
[90214.645505] EtherCAT 0: Starting EtherCAT-IDLE thread.
[90214.648869] EtherCAT 0: Slave states on main device: INIT.
[90214.657325] EtherCAT 0: Slave states on main device: PREOP.
[90214.722624] EtherCAT 0: Releasing master...
[90214.722654] EtherCAT 0: Released.
[90215.184156] EtherCAT: Requesting master 0...
[90215.184180] EtherCAT: Successfully requested master 0.
[90218.289932] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[90218.289939] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 00000000c1b9caca.
[90218.291662] EtherCAT 0: Master thread exited.
[90218.291669] EtherCAT 0: Starting EtherCAT-OP thread.
[90218.291752] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[90218.318755] EtherCAT 0: Slave states on main device: INIT.
[90218.330753] EtherCAT 0: Slave states on main device: PREOP.
[90218.662754] EtherCAT 0: Slave states on main device: SAFEOP.
[90218.666753] EtherCAT 0: Slave states on main device: OP.
[90321.352764] EtherCAT 0: Master thread exited.
[90321.352783] EtherCAT 0: Starting EtherCAT-IDLE thread.
[90321.353089] EtherCAT ERROR 0-main-0: Failed to receive AL state datagram: Datagram initialized.
[90321.357221] EtherCAT 0: Slave states on main device: INIT.
[90321.363777] EtherCAT 0: Slave states on main device: PREOP.
[90321.433924] EtherCAT 0: Releasing master...
[90321.433931] EtherCAT 0: Released.
[90321.503409] EtherCAT WARNING: Datagram 00000000e9609eb2 (master-fsm) was SKIPPED 1 time.
[90323.429890] EtherCAT: Requesting master 0...
[90323.429896] EtherCAT: Successfully requested master 0.
[90326.544937] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[90326.544943] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 00000000c1b9caca.
[90326.545489] EtherCAT 0: Master thread exited.
[90326.545496] EtherCAT 0: Starting EtherCAT-OP thread.
[90326.546152] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[90326.567210] EtherCAT 0: Slave states on main device: INIT.
[90326.579194] EtherCAT 0: Slave states on main device: PREOP.
[90326.911186] EtherCAT 0: Slave states on main device: SAFEOP.
[90326.915199] EtherCAT 0: Slave states on main device: OP.
[90331.675479] EtherCAT 0: Master thread exited.
[90331.675497] EtherCAT 0: Starting EtherCAT-IDLE thread.
[90331.679353] EtherCAT 0: Slave states on main device: INIT.
[90331.687595] EtherCAT 0: Slave states on main device: PREOP.
[90331.752639] EtherCAT 0: Releasing master...
[90331.752645] EtherCAT 0: Released.
[90333.753036] EtherCAT: Requesting master 0...
[90333.753042] EtherCAT: Successfully requested master 0.
[90336.852937] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[90336.852944] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 00000000147aaa60.
[90336.853400] EtherCAT 0: Master thread exited.
[90336.853407] EtherCAT 0: Starting EtherCAT-OP thread.
[90336.863573] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[90336.890579] EtherCAT 0: Slave states on main device: INIT.
[90336.902578] EtherCAT 0: Slave states on main device: PREOP.
[90337.234578] EtherCAT 0: Slave states on main device: SAFEOP.
[90337.238578] EtherCAT 0: Slave states on main device: OP.
[90343.367615] EtherCAT 0: Master thread exited.
[90343.367634] EtherCAT 0: Starting EtherCAT-IDLE thread.
[90343.367891] EtherCAT ERROR 0-main-0: Failed to receive AL state datagram: Datagram initialized.
[90343.372532] EtherCAT 0: Slave states on main device: INIT.
[90343.378660] EtherCAT 0: Slave states on main device: PREOP.
[90343.444630] EtherCAT 0: Releasing master...
[90343.444637] EtherCAT 0: Released.
[90343.526289] EtherCAT WARNING: Datagram 00000000e9609eb2 (master-fsm) was SKIPPED 1 time.
[90343.911236] EtherCAT: Requesting master 0...
[90343.911242] EtherCAT: Successfully requested master 0.
[90347.151964] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[90347.151972] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 0000000054c7af0c.
[90347.152960] EtherCAT 0: Master thread exited.
[90347.152967] EtherCAT 0: Starting EtherCAT-OP thread.
[90347.153097] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[90347.180241] EtherCAT 0: Slave states on main device: INIT.
[90347.192217] EtherCAT 0: Slave states on main device: PREOP.
[90347.524199] EtherCAT 0: Slave states on main device: SAFEOP.
[90347.528206] EtherCAT 0: Slave states on main device: OP.
[90357.403105] EtherCAT 0: Master thread exited.
[90357.403122] EtherCAT 0: Starting EtherCAT-IDLE thread.
[90357.406701] EtherCAT 0: Slave states on main device: INIT.
[90357.412925] EtherCAT 0: Slave states on main device: PREOP.
[90357.483655] EtherCAT 0: Releasing master...
[90357.483662] EtherCAT 0: Released.
[90359.477649] EtherCAT: Requesting master 0...
[90359.477654] EtherCAT: Successfully requested master 0.
[90362.561946] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[90362.561953] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 0000000020105f58.
[90362.563750] EtherCAT 0: Master thread exited.
[90362.563758] EtherCAT 0: Starting EtherCAT-OP thread.
[90362.563852] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[90362.589850] EtherCAT 0: Slave states on main device: INIT.
[90362.601849] EtherCAT 0: Slave states on main device: PREOP.
[90362.933849] EtherCAT 0: Slave states on main device: SAFEOP.
[90362.937848] EtherCAT 0: Slave states on main device: OP.
[91812.736923] EtherCAT 0: Master thread exited.
[91812.736967] EtherCAT 0: Starting EtherCAT-IDLE thread.
[91812.739252] EtherCAT ERROR 0-main-0: Failed to receive AL state datagram: Datagram initialized.
[91812.742377] EtherCAT 0: Slave states on main device: INIT.
[91812.748619] EtherCAT 0: Slave states on main device: PREOP.
[91812.813877] EtherCAT 0: Releasing master...
[91812.813884] EtherCAT 0: Released.
[91812.993613] EtherCAT WARNING: Datagram 00000000e9609eb2 (master-fsm) was SKIPPED 1 time.
[91814.810953] EtherCAT: Requesting master 0...
[91814.810959] EtherCAT: Successfully requested master 0.
[91817.867006] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[91817.867013] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 0000000006a5d054.
[91817.867614] EtherCAT 0: Master thread exited.
[91817.867621] EtherCAT 0: Starting EtherCAT-OP thread.
[91817.868404] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[91817.895418] EtherCAT 0: Slave states on main device: INIT.
[91817.907418] EtherCAT 0: Slave states on main device: PREOP.
[91818.239417] EtherCAT 0: Slave states on main device: SAFEOP.
[91818.243418] EtherCAT 0: Slave states on main device: OP.
[91955.044554] EtherCAT 0: Master thread exited.
[91955.044571] EtherCAT 0: Starting EtherCAT-IDLE thread.
[91955.046785] EtherCAT ERROR 0-main-0: Failed to receive AL state datagram: Datagram initialized.
[91955.049914] EtherCAT 0: Slave states on main device: INIT.
[91955.056296] EtherCAT 0: Slave states on main device: PREOP.
[91955.122943] EtherCAT 0: Releasing master...
[91955.122949] EtherCAT 0: Released.
[91955.136997] EtherCAT WARNING: Datagram 00000000e9609eb2 (master-fsm) was SKIPPED 1 time.
[91957.122329] EtherCAT: Requesting master 0...
[91957.122335] EtherCAT: Successfully requested master 0.
[91960.183014] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[91960.183021] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 00000000b4ecb564.
[91960.183272] EtherCAT 0: Master thread exited.
[91960.183278] EtherCAT 0: Starting EtherCAT-OP thread.
[91960.183368] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[91960.208383] EtherCAT 0: Slave states on main device: INIT.
[91960.220383] EtherCAT 0: Slave states on main device: PREOP.
[91960.552384] EtherCAT 0: Slave states on main device: SAFEOP.
[91960.556384] EtherCAT 0: Slave states on main device: OP.
[92178.599573] EtherCAT 0: Master thread exited.
[92178.599591] EtherCAT 0: Starting EtherCAT-IDLE thread.
[92178.605582] EtherCAT 0: Slave states on main device: INIT.
[92178.611776] EtherCAT 0: Slave states on main device: PREOP.
[92178.672798] EtherCAT 0: Releasing master...
[92178.672805] EtherCAT 0: Released.
[92179.867450] EtherCAT 0: Master thread exited.
[92179.869851] EtherCAT 0: Releasing main device 00:01:C0:2F:E0:C6.
[92179.879750] ec_generic: Unloading.
[92179.891603] EtherCAT: Master module cleaned up.
[92181.965712] br0: port 2(eth1) entered blocking state
[92181.968031] br0: port 2(eth1) entered disabled state
[92181.970453] device eth1 entered promiscuous mode
[92182.514937] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[92184.213382] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[92184.216008] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[92184.218475] br0: port 2(eth1) entered blocking state
[92184.220828] br0: port 2(eth1) entered forwarding state
[94625.023421] br0: port 2(eth1) entered disabled state
[94625.540426] device eth1 left promiscuous mode
[94625.542799] br0: port 2(eth1) entered disabled state
[94625.589855] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[94626.624372] EtherCAT: Master driver 1.5.2-vecsyn-5 gf0c7a0cb
[94626.626850] EtherCAT: 1 master waiting for devices.
[94626.635034] ec_generic: EtherCAT master generic Ethernet device module 1.5.2-vecsyn-5 gf0c7a0cb
[94626.637428] EtherCAT: Accepting 00:01:C0:2F:E0:C6 as main device for master 0.
[94626.639826] ec_generic: Binding socket to interface 5 (eth1).
[94626.648835] EtherCAT 0: Starting EtherCAT-IDLE thread.
[94627.271376] igb 0000:03:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[94627.273984] EtherCAT 0: Link state of ecm0 changed to UP.
[94627.274126] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[94627.281295] EtherCAT 0: 1 slave(s) responding on main device.
[94627.283737] EtherCAT 0: Slave states on main device: SAFEOP + ERROR.
[94627.286721] EtherCAT 0: Scanning bus.
[94627.289448] EtherCAT WARNING 0-main-0: Slave has state error bit set (SAFEOP + ERROR)!
[94627.403617] EtherCAT 0: Bus scanning completed in 117 ms.
[94627.403623] EtherCAT 0: Using slave main-0 as DC reference clock.
[94627.406816] EtherCAT ERROR 0-main-0: AL status message 0x001B: "Sync manager watchdog".
[94627.409493] EtherCAT 0: Slave states on main device: SAFEOP.
[94627.409499] EtherCAT 0-main-0: Acknowledged state SAFEOP.
[94627.411628] EtherCAT 0: Slave states on main device: INIT.
[94627.420713] EtherCAT 0: Slave states on main device: PREOP.
[94627.519493] EtherCAT: Requesting master 0...
[94627.519499] EtherCAT: Successfully requested master 0.
[94630.598110] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[94630.598117] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 0000000006a5d054.
[94630.599477] EtherCAT 0: Master thread exited.
[94630.599486] EtherCAT 0: Starting EtherCAT-OP thread.
[94630.599585] EtherCAT WARNING 0: 1 datagram TIMED OUT!
[94630.626600] EtherCAT 0: Slave states on main device: INIT.
[94630.638599] EtherCAT 0: Slave states on main device: PREOP.
[94630.970599] EtherCAT 0: Slave states on main device: SAFEOP.
[94630.974599] EtherCAT 0: Slave states on main device: OP.
[94846.695687] EtherCAT 0: Master thread exited.
[94846.695704] EtherCAT 0: Starting EtherCAT-IDLE thread.
[94846.699499] EtherCAT 0: Slave states on main device: INIT.
[94846.707767] EtherCAT 0: Slave states on main device: PREOP.
[94846.773760] EtherCAT 0: Releasing master...
[94846.773767] EtherCAT 0: Released.
[94848.775620] EtherCAT: Requesting master 0...
[94848.775626] EtherCAT: Successfully requested master 0.
[94851.973122] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[94851.973130] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 0000000043b2317f.
[94851.973235] EtherCAT 0: Master thread exited.
[94851.973241] EtherCAT 0: Starting EtherCAT-OP thread.
[94851.975177] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[94852.002395] EtherCAT 0: Slave states on main device: INIT.
[94852.014399] EtherCAT 0: Slave states on main device: PREOP.
[94852.346398] EtherCAT 0: Slave states on main device: SAFEOP.
[94852.350409] EtherCAT 0: Slave states on main device: OP.
[94858.616173] EtherCAT 0: Master thread exited.
[94858.616190] EtherCAT 0: Starting EtherCAT-IDLE thread.
[94858.616912] EtherCAT ERROR 0-main-0: Failed to receive AL state datagram: Datagram initialized.
[94858.620126] EtherCAT 0: Slave states on main device: INIT.
[94858.627792] EtherCAT 0: Slave states on main device: PREOP.
[94858.692963] EtherCAT 0: Releasing master...
[94858.692970] EtherCAT 0: Released.
[94858.882734] EtherCAT WARNING: Datagram 00000000dca7e538 (master-fsm) was SKIPPED 1 time.
[94860.691652] EtherCAT: Requesting master 0...
[94860.691657] EtherCAT: Successfully requested master 0.
[94863.809140] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[94863.809147] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 00000000b4ecb564.
[94863.809633] EtherCAT 0: Master thread exited.
[94863.809640] EtherCAT 0: Starting EtherCAT-OP thread.
[94863.810217] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[94863.837400] EtherCAT 0: Slave states on main device: INIT.
[94863.849419] EtherCAT 0: Slave states on main device: PREOP.
[94864.181409] EtherCAT 0: Slave states on main device: SAFEOP.
[94864.185404] EtherCAT 0: Slave states on main device: OP.
[94978.922234] EtherCAT 0: Master thread exited.
[94978.922251] EtherCAT 0: Starting EtherCAT-IDLE thread.
[94978.922481] EtherCAT ERROR 0-main-0: Failed to receive AL state datagram: Datagram initialized.
[94978.925631] EtherCAT 0: Slave states on main device: INIT.
[94978.931842] EtherCAT 0: Slave states on main device: PREOP.
[94979.002284] EtherCAT 0: Releasing master...
[94979.002291] EtherCAT 0: Released.
[94979.002826] EtherCAT WARNING: Datagram 00000000dca7e538 (master-fsm) was SKIPPED 1 time.
[94981.003061] EtherCAT: Requesting master 0...
[94981.003066] EtherCAT: Successfully requested master 0.
[94984.200148] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[94984.200155] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 0000000043b2317f.
[94984.200774] EtherCAT 0: Master thread exited.
[94984.200780] EtherCAT 0: Starting EtherCAT-OP thread.
[94984.201493] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[94984.226500] EtherCAT 0: Slave states on main device: INIT.
[94984.238498] EtherCAT 0: Slave states on main device: PREOP.
[94984.570499] EtherCAT 0: Slave states on main device: SAFEOP.
[94984.574498] EtherCAT 0: Slave states on main device: OP.
[94997.479705] EtherCAT 0: Master thread exited.
[94997.479723] EtherCAT 0: Starting EtherCAT-IDLE thread.
[94997.483768] EtherCAT 0: Slave states on main device: INIT.
[94997.492007] EtherCAT 0: Slave states on main device: PREOP.
[94997.563727] EtherCAT 0: Releasing master...
[94997.563734] EtherCAT 0: Released.
[94999.566182] EtherCAT: Requesting master 0...
[94999.566187] EtherCAT: Successfully requested master 0.
[95002.687156] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[95002.687163] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 0000000054c7af0c.
[95002.687540] EtherCAT 0: Master thread exited.
[95002.687546] EtherCAT 0: Starting EtherCAT-OP thread.
[95002.687994] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[95002.716001] EtherCAT 0: Slave states on main device: INIT.
[95002.728000] EtherCAT 0: Slave states on main device: PREOP.
[95003.060000] EtherCAT 0: Slave states on main device: SAFEOP.
[95003.063999] EtherCAT 0: Slave states on main device: OP.
[95250.902110] EtherCAT 0: Master thread exited.
[95250.902130] EtherCAT 0: Starting EtherCAT-IDLE thread.
[95250.905998] EtherCAT 0: Slave states on main device: INIT.
[95250.914318] EtherCAT 0: Slave states on main device: PREOP.
[95250.983165] EtherCAT 0: Releasing master...
[95250.983171] EtherCAT 0: Released.
[95252.981517] EtherCAT: Requesting master 0...
[95252.981524] EtherCAT: Successfully requested master 0.
[95256.081165] EtherCAT 0: Domain0: Logical address 0x00000000, 82 byte, expected working counter 3.
[95256.081172] EtherCAT 0: Datagram domain0-0-main: Logical offset 0x00000000, 82 byte, type LRW at 00000000c1b9caca.
[95256.082532] EtherCAT 0: Master thread exited.
[95256.082540] EtherCAT 0: Starting EtherCAT-OP thread.
[95256.091252] EtherCAT WARNING 0: 1 datagram UNMATCHED!
[95256.118409] EtherCAT 0: Slave states on main device: INIT.
[95256.130446] EtherCAT 0: Slave states on main device: PREOP.
[95256.462423] EtherCAT 0: Slave states on main device: SAFEOP.
[95256.466425] EtherCAT 0: Slave states on main device: OP.

philippeH

https://docs.motorcortex.io/docs/motorcortex-io-tools/motorcortex-ecat/troubleshoot-ecat/#ethercat-error-0-main-x-al-status-message-0x0030-invalid-dc-synch-configuration
https://docs.motorcortex.io/docs/motorcortex-io-tools/motorcortex-ecat/device-configuration-panel/distributed_clock/

Did you fill in DC Clock setting according to Assign activate value As described in this example (decimal representation)?

AbhilashIngale

philippeH
Yes, we filled the Assign Activate field as per the following lines in our .xml -

		<OpMode>
						<Name>Freerun</Name>
						<Desc>Free Run</Desc>
						<AssignActivate>#x00</AssignActivate>
					</OpMode>
					<OpMode>
						<Name>DC</Name>
						<Desc>DC-Synchron</Desc>
						<AssignActivate>#x300</AssignActivate>
						<CycleTimeSync0 Factor="1">1000000</CycleTimeSync0>
						<ShiftTimeSync0>0</ShiftTimeSync0>
						<CycleTimeSync1 Factor="0">0</CycleTimeSync1>
						<ShiftTimeSync1>0</ShiftTimeSync1>
					</OpMode>

This value hex 300 corresponds to a dec value of 768.

philippeH

What kind of motion controller hardware are you using?
Also please checkout your system load: Inside the DESK-Tool check:
root/Control_task/utilization_max
root/Fieldbus_task/utilization_max

AbhilashIngale

philippeH
Do you mean the hardware on which I am running MCX? That is the standard Fitlet2 IPC.

root/Control_task/utilization_max load is 24-25
root/Fieldbus_task/utilization_max is 32-34

philippeH

What is the watchdog time specified in your slave?

Error Code 0x001B
Meaning
Sync manager watchdog

Description
The slave did not receive process data within the specified watchdog time. Usually, the WD time is 100ms. The WD is re-started every time it receives new process data, usually when the Output SyncManager (SyncManager2) is written. For devices which have only inputs usually no WD is used. Increasing the WD is not a solution.

Reason: PLC stopped

Current State (or state change)
O, S

Resulting state
S + E

Solution
n/a

AbhilashIngale

philippeH

I am not sure what the watchdog time is on the slave. In the .esi file I see the following fields that make the most sense to me -

									<SubItem>
										<Name>Watchdog Time</Name>
										<Info>
											<MinData>0100</MinData>
											<MaxData>FFFF</MaxData>
											<DefaultData>3200</DefaultData>
										</Info>
									</SubItem>

Could we infer the time from these fields or should I check somewhere else in the slave .esi?

philippeH

The system load seems to be fine:

What you could do as workaround:
<Sm MinSize="1" MaxSize="300" DefaultSize="35" StartAddress="#x1800" ControlByte="#x24" Enable="1">Outputs</Sm>
This disables the syncmanagerwatch dog function.

AbhilashIngale

philippeH

Disabling the watchdog with the controlbyte field seems to have worked.

[   12.502807] EtherCAT 0: Bus scanning completed in 571 ms.
[   12.502815] EtherCAT 0: Using slave main-0 as DC reference clock.

Although I am curious why does it not work as per the documentation on your website. Could you explain this in detail on what happened and how to avoid it? Is it something specific to the Application I am running or is it something with the ECAT-Slave?

philippeH

Some more questions:
What kind of MCX image version are you using?
What kind of application and version are you using?
Are you also running some python script on the background?
What is the root/Control_task/absolute_cycle_max
What is the root/Fieldbus_task/absolute_cycle_max

AbhilashIngale

philippeH thanks for the comments.

Here are the details:

OS image version: mcx-image-dev-mcx-intel-2024.01-0-g8aa3837.wic.xz
Currently, there is no application running. I am on the first step of configuring DC through ECAT. Don't know if that is a problem.
There is nothing custom running on the IPC or interacting with it.
I will check in some time.

I will try your suggestions and get back to you with more info on #4.

Cheers.

AbhilashIngale

philippeH

The parameter values which you previously requested are:

root/Control_task/absolute_cycle_max : 1012
root/Control_task/actual_cycle_max : 1002
root/Fieldbus_task/absolute_cycle_max: 1008
root/Fieldbus_task/actual_cycle_max : 1002

philippeH

You were able to enter the desk-tool, so there must be an application running else this would have not been possible.

Part of the version you can find in the desk under:
root/AppInfo/versions/app&control&core&xxx

Also you can see it in the version number of the application, when you deploy it from the portal to the mcx-controller.
For example:

AbhilashIngale

philippeH

You are right, I am running an app with the following details: